Superior terrain capability
The Gator™ XUV Crossover Series Utility Vehicle has a precision-engineered drivetrain system that fully utilizes engine power, optimizing acceleration, hauling, towing, and hill-climbing capabilities. Power is transmitted from the engine through a continuously variable clutch system to the transaxle.
Key elements of the drive system include:
Variable-speed drive
The variable-speed drive consists of two clutches and a drive belt:
- Drive clutch is attached to the engine.
- Driven clutch is attached to the transaxle.
Features include:
- The engine braking system utilizes a tight belt for operation, requiring an idler sleeve on the primary clutch for neutral. The secondary clutch is a build-on-shaft design that utilizes a cam to tune the acceleration and deceleration of the vehicle. The clutch will stay engaged, providing deceleration until approximately 5 km/h (3 mph).
- The continuously variable transmission (CVT) air intake draws in cool air to reduce heat and the amount of water ingestion into the CVT system. The system will reduce belt slippage and improve durability.
- A low- and high-speed forward gear offering:
- Low range is 0 km/h to 40 km/h (0 mph to 25 mph), XUV835
- Low range is 0 km/h to 24 km/h (0 mph to 15 mph), XUV865
- High range is 0 km/h to 72 km/h (0 mph to 45 mph), XUV835
- High range is 0 km/h to 45 km/h (0 mph to 28 mph), XUV865
- Ability to creep along slowly to maneuver in tight spaces
- Standard full-clutch enclosure with high speed fan provides longer belt and clutch life
- High-ratio clutches with three cam weights for maximum belt-clamp load in high torque conditions
NOTE: Delivery of torque to the ground and top speed depends on tire size, which is a function of nominal size and pressure.
How the variable-speed drive works:
- As engine speed increases, the spring-loaded drive clutch is closed by weights being forced out by centrifugal force.
- As the drive clutch closes, the belt rides up to the largest diameter of the drive clutch and forces open the driven clutch.
- With the belt running in the smallest diameter of the driven clutch, the speed being transferred to the transaxle is increased.
- The driven clutch is designed to sense varying loads (inclines, mud, etc.) and constantly adjusts drive speed upward or downward so that engine rpm remains optimal.
Transaxle, mechanical front-wheel drive (MFWD), and constant velocity (CV) shafts
Operator interface features:
- Selectable four-wheel drive (4WD) system with a limited slip front differential and dash-mounted electronic rocker switch
- Provides exceptional traction in challenging conditions
- Near instantaneous torque to the front wheels once rocker switch is engaged
- Maintains turf-friendly operation in two-wheel drive (2WD) mode
- Combined with rear traction assist (differential lock), provides excellent traction in challenging conditions
- More control descending hills with 4WD engaged as all four wheels help slow the vehicle down
- Clutch engagement still necessary to prevent free coasting
Transaxle features:
- Low, high, neutral, reverse, and park transaxle
- Automotive-style, integrated park position in transmission
- Low range for maximum torque delivered to the wheels for hauling, pushing, and pulling
- High range for maximum vehicle speed
- To shift out of park, service brake must be pressed to release the parking solenoid. An audible click will be heard and allows the vehicle to shift out of park into the desired gear.
NOTE: Differential design reduces scuffing of the turf during turns because it allows the inside wheels to turn slower than the outside wheels.
- Start in gear, neutral, or park position for quick starting. The service brake must be engaged to start when in gear or neutral.
- For operators living in regions with homologation requirements or certain bid language stating the need for a secondary park brake, such as governmental or municipalities, a secondary park brake is available as an option on select models:
- HPX615E
- HPX815E
- XUV825 S4
- XUV855 S4
- XUV835M
- XUV835R
- XUV865M
- XUV865R
- Large, sealed bearings are located inside the housing for better protection and durability
- Contains gear case for transferring power to the MFWD
- Splined shaft interfaces for maximum torque transfer and durability
- All drive gears machined from highest grade gear steel
- Protected by a skid plate
MFWD features:
- Electronically selectable by the operator
- Offers limited slip functionality for precision steering and great traction while pointing and shooting out of a corner.
- Vertically oriented oil drain for easy maintenance
- Protected by a steel skid plate and frame
Drive shaft features:
- Rear CV shaft diameter measures 27 mm (1.1 in.) and is designed for peak engine and braking torque
- Front CV shaft diameter measures 23 mm (0.91 in.) and is designed for peak engine torque
- Propshaft is designed for peak engine torque
- All CV shaft and propshaft joints are maintenance free and protected by exclusive thermoplastic elastomer (TPE) boots for durability
Roomy and quiet operator station
Whether it is a completely open operator station or a factory installed cab, the interior has been redesigned with comfort and ergonomics in mind.
- Gear shift control and differential switch on the dash
HVAC dash shown (R trim) |
- Tilt steering
Tilt steering | Tilt steering (up position) | Tilt steering (down position) |
- Bench seat with driver adjustment
Bench seat adjustment |
- Three-wide seating
Seating |
Powerful gas engine delivers superb starting, idling, and throttle response
The machine is powered by an 812-cm3 (49.6-cu in.), 3-cylinder, dual overhead cams, liquid-cooled, four-cycle gasoline engine. It produces 6.5 kgm (47 lb-ft) of torque at 3200 rpm. The advanced electronic controls and fuel-injection system deliver superb starting, idling, and throttle response during operation.
The engine offers the following performance and reliability features:
- 40.3 kW (54 hp*) at 6000 rpm
- 72-km/h (45-mph) top speed
- Electronic fuel injection for superb performance, altitude adjustment, and cold-weather starting (tested to -28.9°C [-20°F])
- Electronic ignition is continuously variable for optimum engine power and provides fast, reliable starts
- Exclusive electronic ground-speed governor and throttle body
- Auto-compensates by providing more power when going up a hill or through difficult terrain
- Eliminates top-speed degradation from belt wear
- Overhead valve design provides greater efficiency and fuel economy
- Full-pressure lubrication system
- Spin-on oil filter with drain bracket and oil drain plug enable easy servicing
- Dry, replaceable, single-element air cleaner with remote intake
- See-through coolant recovery tank permits the operator to check the coolant level without having to remove the radiator cap
- Open front grille allows air flow and proper ventilation to the radiator
- Standard high-capacity alternator – 85 amps for maximum accessory capability
*The engine horsepower information is provided by the engine manufacturer to be used for comparison purposes only. The actual operating horsepower will be less.
Dual A-arm front and rear suspension provides a smooth ride over challenging terrain and excellent hauling characteristics
To complement the robust frame, the XUV is equipped with four-wheel independent suspension.
A dual A-arm front and rear suspension provides a smooth ride over challenging terrain and excellent hauling characteristics.
The entire suspension system has been optimized to handle no cargo to maximum cargo without compromising ride quality or vehicle stability.
Dual A-arm independent front suspension features include:
- 200.7 mm (7.9 in.) of travel provides ample wheel travel to keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
- Heavy-duty nodular cast-iron knuckles support the constant-velocity (CV) shaft and wheel
- Maintenance-free rubber torsional A-arm pivots for long life and quiet operation
- CV shaft protection from sticks that may puncture the rubber boot
- Coil-over shocks absorb the most demanding terrain
Dual A-arm independent rear suspension features include:
- Unequal length and dual A-arm construction for superior wheel control and travel
- 231.14 mm (9.1 in.) of total travel provides ample wheel travel to keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
- Coil-over shocks absorb the most demanding terrain
- A-arms made from square/rectangular tubing reduce weight while remaining rigid
- Heavy-duty nodular cast-iron uprights support wheel loads with a double row of ball bearings
- CV driveshaft protection from sticks that may puncture the rubber boot
- Rear sway bar for lateral stability
Extra-durable deluxe cargo box ensures hard-working performance and longevity
The deluxe cargo box consists of a 15 percent glass-filled polypropylene composite material that eliminates rust and dents and reduces noise.
Deluxe cargo box tailgate
The tailgate can be opened or removed for easier cleanout and to carry longer items. The tailgate has been improved, features truck-like performance, and can be operated with one hand.
The standard-installed lanyards can also be removed to lower the tailgate to 150 degrees for convenient loading and unloading tasks.
Deluxe cargo box tilt
The deluxe cargo box is easier to latch, unlatch, raise, and lower with the integrated handle design and gas assist.
A prop rod is provided to hold the box in the upright position for operator convenience, as well as limit box pivot travel.
Integrated tie-down points
The deluxe cargo box offers integrated tie-down points for increased versatility. Tie-down points are located in the following areas:
- Four corners inside the cargo box bed
- Four points on the load guard directly behind the operator station (A)
- Tie-down bars on either side of the cargo box (B)
- Six points on the underside of the cargo box frame (circled)
Converting deluxe cargo box to a flatbed
Optional accessories for the deluxe cargo box:
- See attachment information in the Value Selling Navigator
Specifications
Length | 1143 mm (45 in.) |
Width | 1320 mm (52 in.) |
Depth | 304 mm (12 in.) |
Volume | 0.46 m3 (16.4 cu ft) |
Weight capacity | 454 kg (1000 lb) |
Dump angle | 47 degrees |
CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.
E-trim details and electrical system
The E trim has no electric power-assist steering (EPAS) and has minimal electronic connections. This trim level is open station only.
On E-trim vehicles, adding attachments and accessories requires additional electrical harnesses and structure. See the chart below for information regarding what is required for attachments and accessories.
Cargo box lift | Backup alarm | Brake / tail / reverse lights | Speed limiter kit | Base radio | Heater | 2041-kg (4500-lb) winch | Premium radio (base radio kit needed) | LED lights – front OPS | Windshield wiper | Windshield washer | LED lights – brush guard | LED headlights | Turn signals | Horn | Beacon light | LED lights – rear OPS | Sprayers | Spreaders | AMS integration kit | |
E | a | a | a,c | a,c,d | a,c,d | a,c,d | a,b | a,b | a,b | a,b | a,c,e | a,c,e | a,f | a,f | a,c,e,f | |||||
M open | c | c,d | c,d | c,d | b | b | b | b | c,e | c,e | f | f | c,e,f | |||||||
M cab | b | b | b | b | e | e | f | f | e,f | |||||||||||
R | f | f | f |
= connections in base harness | |
a | E-spec attachment harness |
b | Front attachments harness |
c | Roof attachment harness |
d | Front cab harness |
e | Rear cab harness |
f | Dash port harness |
* | If blank, the base chassis harness has the connector for the attachment |
If dual beam headlights are desired, the following bundles are required:
XUV835E/865E:
- BM26589 – dual beam LED headlights, including three-position rocker switch
- BUC10809 – front light harness kit
- BUC10810 – E-spec attachment harness
XUV835M/865M:
- BM26589 – dual beam LED headlights, including three-position rocker switch
- BUC10809 – front light harness kit
XUV835R/865R:
- BM26589 – dual beam LED headlights, including three-position rocker switch
Build-to-order options
- Roof is standard on all units – can order less roof on open station units
- Available factory-installed winch on M- and R-trim units
- Available factory-installed front glass windshield on M-trim open station units
- Available factory-installed rear glass panel on M-trim open station units
- Available factory-installed brush guard
- Available factory-installed brush guard extensions
- Available factory-installed rear cargo box fender guards (rear bumper required, also factory installed)